-
Frequent Poster
Tanks
Sorry, I'm not sure where to post something like this, but lets try here -
what would be the price of a used Dye 70/45 stubby? For example how much would one with hydro in 2012 be? or 2013?
Thank you.
-
Pballa
-
Frequent Poster
for both 2012/2013?
they a good tank?
Last edited by K-Math; 02-16-2010 at 07:08 PM.
Reason: Automerged Doublepost
-
Pballa
Yeah they are. stubbies are usually good if u r front tho cuz of the capacity of the tank. but yeah they are good tanks
-
Frequent Poster
what kind of tank would you suggest for back/mid?
-
Pballa
probably a 68/45, u should get more advice tho b4 you go out and buy 1
-
Frequent Poster
whats the difference between 68/45 and a 70/45? is it that much of a difference?
-
Frequent Poster
-
Frequent Poster
the 70/4500 is physically smaller than the 68/4500 though.
-
Pballa
Actually the 70/45 has a larger volume then the 68/45. It's "smaller" in that its shorter, but it makes up for it in being fatter as it's width is greater. The 68/45 appears to be "larger" in that its length is longer and its width is shorter. That's why there's a difference in size, but each tank either makes up for shorter length in a wider width, or longer length for a shorter width.
Just my 2 cents, correct me if I'm wrong.
-
Frequent Poster
Makes sense, and now we may be getting into logistics, but do they not both hold 4500 psi of air? cause thats what the gauge is, which doesnt make sense because it is 70 cu inches. so this is where i am lost. I'm looking for the one that can old the most air, I dont care about size.
-
Pballa
Well 4500 psi is the pounder per square inch that the air inside exerts on the cylinder. It's the cubic inches that determine the volume of air that can be held. So in short, if your looking for a tank that hold the most air, get the one with the biggest cubic inches. I've heard of some that range in the 90's haha, but those are quite chunky.
-
Frequent Poster
Oh alright, but then why are gauges in psi? I feel lik a noob.
-
Pballa
Well the gauges are used to show the pressure that the air inside is under. Each shot you take requires a certain volume, and pressure of air. So as you use up the air the pressure gradually decreases.
-
Frequent Poster
But lets say when your filling up your tank, it doesnt show that there is a difference in air used between the 68 and 70/4500 - is this cause its supposed to be common sense, or for other reasons.
-
Pballa
-
Frequent Poster
At PAG, when you go to fill up your air tank, the gauge reads "psi * 1000" or what not. This meaning it will fill the tank to it reaches 4.5 on the gauge. Why does it not say Cu INCHES filled? cause the 68/4500 and 70/4500 both hold 4500 psi.
-
Pballa
Well I mean technically the tank in cubic inches is already "full" in that there is already air inside, if there wasn't it'd create a vacuum and essentially collapse on itself. The gauge reads the pressure because thats essentially what your doing, your adding more pressure to the tank by adding more air into it.
Thats the general process I believe.
-
OMG!!!!!!
You're looking at this from the wrong angle. How much air a tank holds is determined by both the volume and pressure.
At atmospheric pressure, a 68ci tank will hold 68 cubic inches while a 70ci tank will hold 70. When you start filling them, the same amount of air will end up being less pressure in the 70 cubic inch due to the higher volume, but when both are filled to 4500psi, the higher volume tank holds more air. To get an accurate volume of air, you need both the volume of the tank and pressure combined.
Last edited by mtaylor; 02-16-2010 at 10:44 PM.
Reason: Automerged Doublepost
-
Member
i got a 68/4500 ill trade you for a stubby
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
Bookmarks